1.  Introduction This   battery   pack   System,   is   applicable   both  for   residential   and commercial energy storage system, which is assembled with 3.2V 200Ah lithium iron phosphate cell in 4P16S configuration, And intelligent BMS form 51.2V200Ah lithium battery system.  Each  pack  support  16packs  in  parallel  to  easily expand capacity. Do not mix parallel the battery packs of different brands or models. 1.   Functions l Battery voltage calculation: 16 battery voltage sampling test, deviation ± 20mV l Battery and ambient temperature detection: 4 battery temperature sensors, 1 ambient temperature sensor, 1 MOS temperature sensor, deviation ± 2 ℃. l Battery capacity and cycle times: complete a complete charging, discharging cycle to set the actual capacity. Monitor the remaining capacity of the battery with the capacity estimation accuracy within 5% deviation. In addition, the charging and discharging cycle time and the complete charging and discharging cycle time can be configured. l Smart cell balance: charging and static balance strategies can be flexibly set to effectively extend the service life. l Communication interface: PC or intelligent front-end can monitor battery data, control operation and set parameters through telemetry, remote signaling, remote adjustment, remote control and other commands. The communication protocol meets the requirements of YD/T 1363.3 and realizes cascade communication l Historical data recording, saving and reading: when the battery is abnormal, record and save real-time battery status and alarm information. At present, up to 500 historical fault data can be stored. l Battery management system parameter setting: battery management system parameters, including cell battery over voltage/under voltage, battery total voltage over voltage/under voltage, charge and discharge over current, battery high/low temperature, battery capacity, working mode, charge and discharge limit current, can be set in the battery monitoring system. l Working mode: charging and discharging current limiting, constant voltage output, direct output and other working modes can be set in the monitoring system   l Multiple protection functions: hardware protection, battery protection, high and low temperature protection, output short circuit prot

1.  Introduction This   battery   pack   System,   is   applicable   both  for   residential   and commercial energy storage system, which is assembled with 3.2V 200Ah lithium iron phosphate cell in 4P16S configuration, And intelligent BMS form 51.2V200Ah lithium battery system.  Each  pack  support  16packs  in  parallel  to  easily expand capacity. Do not mix parallel the battery packs of different brands or models. 1.   Functions l Battery voltage calculation: 16 battery voltage sampling test, deviation ± 20mV l Battery and ambient temperature detection: 4 battery temperature sensors, 1 ambient temperature sensor, 1 MOS temperature sensor, deviation ± 2 ℃. l Battery capacity and cycle times: complete a complete charging, discharging cycle to set the actual capacity. Monitor the remaining capacity of the battery with the capacity estimation accuracy within 5% deviation. In addition, the charging and discharging cycle time and the complete charging and discharging cycle time can be configured. l Smart cell balance: charging and static balance strategies can be flexibly set to effectively extend the service life. l Communication interface: PC or intelligent front-end can monitor battery data, control operation and set parameters through telemetry, remote signaling, remote adjustment, remote control and other commands. The communication protocol meets the requirements of YD/T 1363.3 and realizes cascade communication l Historical data recording, saving and reading: when the battery is abnormal, record and save real-time battery status and alarm information. At present, up to 500 historical fault data can be stored. l Battery management system parameter setting: battery management system parameters, including cell battery over voltage/under voltage, battery total voltage over voltage/under voltage, charge and discharge over current, battery high/low temperature, battery capacity, working mode, charge and discharge limit current, can be set in the battery monitoring system. l Working mode: charging and discharging current limiting, constant voltage output, direct output and other working modes can be set in the monitoring system   l Multiple protection functions: hardware protection, battery protection, high and low temperature protection, output short circuit prot

1.  Introduction This   battery   pack   System,   is   applicable   both  for   residential   and commercial energy storage system, which is assembled with 3.2V 200Ah lithium iron phosphate cell in 4P16S configuration, And intelligent BMS form 51.2V200Ah lithium battery system.  Each  pack  support  16packs  in  parallel  to  easily expand capacity. Do not mix parallel the battery packs of different brands or models. 1.   Functions l Battery voltage calculation: 16 battery voltage sampling test, deviation ± 20mV l Battery and ambient temperature detection: 4 battery temperature sensors, 1 ambient temperature sensor, 1 MOS temperature sensor, deviation ± 2 ℃. l Battery capacity and cycle times: complete a complete charging, discharging cycle to set the actual capacity. Monitor the remaining capacity of the battery with the capacity estimation accuracy within 5% deviation. In addition, the charging and discharging cycle time and the complete charging and discharging cycle time can be configured. l Smart cell balance: charging and static balance strategies can be flexibly set to effectively extend the service life. l Communication interface: PC or intelligent front-end can monitor battery data, control operation and set parameters through telemetry, remote signaling, remote adjustment, remote control and other commands. The communication protocol meets the requirements of YD/T 1363.3 and realizes cascade communication l Historical data recording, saving and reading: when the battery is abnormal, record and save real-time battery status and alarm information. At present, up to 500 historical fault data can be stored. l Battery management system parameter setting: battery management system parameters, including cell battery over voltage/under voltage, battery total voltage over voltage/under voltage, charge and discharge over current, battery high/low temperature, battery capacity, working mode, charge and discharge limit current, can be set in the battery monitoring system. l Working mode: charging and discharging current limiting, constant voltage output, direct output and other working modes can be set in the monitoring system   l Multiple protection functions: hardware protection, battery protection, high and low temperature protection, output short circuit prot

1.  Introduction This   battery   pack   System,   is   applicable   both  for   residential   and commercial energy storage system, which is assembled with 3.2V 200Ah lithium iron phosphate cell in 4P16S configuration, And intelligent BMS form 51.2V200Ah lithium battery system.  Each  pack  support  16packs  in  parallel  to  easily expand capacity. Do not mix parallel the battery packs of different brands or models. 1.   Functions l Battery voltage calculation: 16 battery voltage sampling test, deviation ± 20mV l Battery and ambient temperature detection: 4 battery temperature sensors, 1 ambient temperature sensor, 1 MOS temperature sensor, deviation ± 2 ℃. l Battery capacity and cycle times: complete a complete charging, discharging cycle to set the actual capacity. Monitor the remaining capacity of the battery with the capacity estimation accuracy within 5% deviation. In addition, the charging and discharging cycle time and the complete charging and discharging cycle time can be configured. l Smart cell balance: charging and static balance strategies can be flexibly set to effectively extend the service life. l Communication interface: PC or intelligent front-end can monitor battery data, control operation and set parameters through telemetry, remote signaling, remote adjustment, remote control and other commands. The communication protocol meets the requirements of YD/T 1363.3 and realizes cascade communication l Historical data recording, saving and reading: when the battery is abnormal, record and save real-time battery status and alarm information. At present, up to 500 historical fault data can be stored. l Battery management system parameter setting: battery management system parameters, including cell battery over voltage/under voltage, battery total voltage over voltage/under voltage, charge and discharge over current, battery high/low temperature, battery capacity, working mode, charge and discharge limit current, can be set in the battery monitoring system. l Working mode: charging and discharging current limiting, constant voltage output, direct output and other working modes can be set in the monitoring system   l Multiple protection functions: hardware protection, battery protection, high and low temperature protection, output short circuit prot

1.  Introduction This   battery   pack   System,   is   applicable   both  for   residential   and commercial energy storage system, which is assembled with 3.2V 200Ah lithium iron phosphate cell in 4P16S configuration, And intelligent BMS form 51.2V200Ah lithium battery system.  Each  pack  support  16packs  in  parallel  to  easily expand capacity. Do not mix parallel the battery packs of different brands or models. 1.   Functions l Battery voltage calculation: 16 battery voltage sampling test, deviation ± 20mV l Battery and ambient temperature detection: 4 battery temperature sensors, 1 ambient temperature sensor, 1 MOS temperature sensor, deviation ± 2 ℃. l Battery capacity and cycle times: complete a complete charging, discharging cycle to set the actual capacity. Monitor the remaining capacity of the battery with the capacity estimation accuracy within 5% deviation. In addition, the charging and discharging cycle time and the complete charging and discharging cycle time can be configured. l Smart cell balance: charging and static balance strategies can be flexibly set to effectively extend the service life. l Communication interface: PC or intelligent front-end can monitor battery data, control operation and set parameters through telemetry, remote signaling, remote adjustment, remote control and other commands. The communication protocol meets the requirements of YD/T 1363.3 and realizes cascade communication l Historical data recording, saving and reading: when the battery is abnormal, record and save real-time battery status and alarm information. At present, up to 500 historical fault data can be stored. l Battery management system parameter setting: battery management system parameters, including cell battery over voltage/under voltage, battery total voltage over voltage/under voltage, charge and discharge over current, battery high/low temperature, battery capacity, working mode, charge and discharge limit current, can be set in the battery monitoring system. l Working mode: charging and discharging current limiting, constant voltage output, direct output and other working modes can be set in the monitoring system   l Multiple protection functions: hardware protection, battery protection, high and low temperature protection, output short circuit prot

1.  Introduction This   battery   pack   System,   is   applicable   both  for   residential   and commercial energy storage system, which is assembled with 3.2V 200Ah lithium iron phosphate cell in 4P16S configuration, And intelligent BMS form 51.2V200Ah lithium battery system.  Each  pack  support  16packs  in  parallel  to  easily expand capacity. Do not mix parallel the battery packs of different brands or models. 1.   Functions l Battery voltage calculation: 16 battery voltage sampling test, deviation ± 20mV l Battery and ambient temperature detection: 4 battery temperature sensors, 1 ambient temperature sensor, 1 MOS temperature sensor, deviation ± 2 ℃. l Battery capacity and cycle times: complete a complete charging, discharging cycle to set the actual capacity. Monitor the remaining capacity of the battery with the capacity estimation accuracy within 5% deviation. In addition, the charging and discharging cycle time and the complete charging and discharging cycle time can be configured. l Smart cell balance: charging and static balance strategies can be flexibly set to effectively extend the service life. l Communication interface: PC or intelligent front-end can monitor battery data, control operation and set parameters through telemetry, remote signaling, remote adjustment, remote control and other commands. The communication protocol meets the requirements of YD/T 1363.3 and realizes cascade communication l Historical data recording, saving and reading: when the battery is abnormal, record and save real-time battery status and alarm information. At present, up to 500 historical fault data can be stored. l Battery management system parameter setting: battery management system parameters, including cell battery over voltage/under voltage, battery total voltage over voltage/under voltage, charge and discharge over current, battery high/low temperature, battery capacity, working mode, charge and discharge limit current, can be set in the battery monitoring system. l Working mode: charging and discharging current limiting, constant voltage output, direct output and other working modes can be set in the monitoring system   l Multiple protection functions: hardware protection, battery protection, high and low temperature protection, output short circuit prot

1.  Introduction This   battery   pack   System,   is   applicable   both  for   residential   and commercial energy storage system, which is assembled with 3.2V 200Ah lithium iron phosphate cell in 4P16S configuration, And intelligent BMS form 51.2V200Ah lithium battery system.  Each  pack  support  16packs  in  parallel  to  easily expand capacity. Do not mix parallel the battery packs of different brands or models. 1.   Functions l Battery voltage calculation: 16 battery voltage sampling test, deviation ± 20mV l Battery and ambient temperature detection: 4 battery temperature sensors, 1 ambient temperature sensor, 1 MOS temperature sensor, deviation ± 2 ℃. l Battery capacity and cycle times: complete a complete charging, discharging cycle to set the actual capacity. Monitor the remaining capacity of the battery with the capacity estimation accuracy within 5% deviation. In addition, the charging and discharging cycle time and the complete charging and discharging cycle time can be configured. l Smart cell balance: charging and static balance strategies can be flexibly set to effectively extend the service life. l Communication interface: PC or intelligent front-end can monitor battery data, control operation and set parameters through telemetry, remote signaling, remote adjustment, remote control and other commands. The communication protocol meets the requirements of YD/T 1363.3 and realizes cascade communication l Historical data recording, saving and reading: when the battery is abnormal, record and save real-time battery status and alarm information. At present, up to 500 historical fault data can be stored. l Battery management system parameter setting: battery management system parameters, including cell battery over voltage/under voltage, battery total voltage over voltage/under voltage, charge and discharge over current, battery high/low temperature, battery capacity, working mode, charge and discharge limit current, can be set in the battery monitoring system. l Working mode: charging and discharging current limiting, constant voltage output, direct output and other working modes can be set in the monitoring system   l Multiple protection functions: hardware protection, battery protection, high and low temperature protection, output short circuit prot

1.  Introduction This   battery   pack   System,   is   applicable   both  for   residential   and commercial energy storage system, which is assembled with 3.2V 200Ah lithium iron phosphate cell in 4P16S configuration, And intelligent BMS form 51.2V200Ah lithium battery system.  Each  pack  support  16packs  in  parallel  to  easily expand capacity. Do not mix parallel the battery packs of different brands or models. 1.   Functions l Battery voltage calculation: 16 battery voltage sampling test, deviation ± 20mV l Battery and ambient temperature detection: 4 battery temperature sensors, 1 ambient temperature sensor, 1 MOS temperature sensor, deviation ± 2 ℃. l Battery capacity and cycle times: complete a complete charging, discharging cycle to set the actual capacity. Monitor the remaining capacity of the battery with the capacity estimation accuracy within 5% deviation. In addition, the charging and discharging cycle time and the complete charging and discharging cycle time can be configured. l Smart cell balance: charging and static balance strategies can be flexibly set to effectively extend the service life. l Communication interface: PC or intelligent front-end can monitor battery data, control operation and set parameters through telemetry, remote signaling, remote adjustment, remote control and other commands. The communication protocol meets the requirements of YD/T 1363.3 and realizes cascade communication l Historical data recording, saving and reading: when the battery is abnormal, record and save real-time battery status and alarm information. At present, up to 500 historical fault data can be stored. l Battery management system parameter setting: battery management system parameters, including cell battery over voltage/under voltage, battery total voltage over voltage/under voltage, charge and discharge over current, battery high/low temperature, battery capacity, working mode, charge and discharge limit current, can be set in the battery monitoring system. l Working mode: charging and discharging current limiting, constant voltage output, direct output and other working modes can be set in the monitoring system   l Multiple protection functions: hardware protection, battery protection, high and low temperature protection, output short circuit prot

1.  Introduction This   battery   pack   System,   is   applicable   both  for   residential   and commercial energy storage system, which is assembled with 3.2V 200Ah lithium iron phosphate cell in 4P16S configuration, And intelligent BMS form 51.2V200Ah lithium battery system.  Each  pack  support  16packs  in  parallel  to  easily expand capacity. Do not mix parallel the battery packs of different brands or models. 1.   Functions l Battery voltage calculation: 16 battery voltage sampling test, deviation ± 20mV l Battery and ambient temperature detection: 4 battery temperature sensors, 1 ambient temperature sensor, 1 MOS temperature sensor, deviation ± 2 ℃. l Battery capacity and cycle times: complete a complete charging, discharging cycle to set the actual capacity. Monitor the remaining capacity of the battery with the capacity estimation accuracy within 5% deviation. In addition, the charging and discharging cycle time and the complete charging and discharging cycle time can be configured. l Smart cell balance: charging and static balance strategies can be flexibly set to effectively extend the service life. l Communication interface: PC or intelligent front-end can monitor battery data, control operation and set parameters through telemetry, remote signaling, remote adjustment, remote control and other commands. The communication protocol meets the requirements of YD/T 1363.3 and realizes cascade communication l Historical data recording, saving and reading: when the battery is abnormal, record and save real-time battery status and alarm information. At present, up to 500 historical fault data can be stored. l Battery management system parameter setting: battery management system parameters, including cell battery over voltage/under voltage, battery total voltage over voltage/under voltage, charge and discharge over current, battery high/low temperature, battery capacity, working mode, charge and discharge limit current, can be set in the battery monitoring system. l Working mode: charging and discharging current limiting, constant voltage output, direct output and other working modes can be set in the monitoring system   l Multiple protection functions: hardware protection, battery protection, high and low temperature protection, output short circuit prot

1.  Introduction This   battery   pack   System,   is   applicable   both  for   residential   and commercial energy storage system, which is assembled with 3.2V 200Ah lithium iron phosphate cell in 4P16S configuration, And intelligent BMS form 51.2V200Ah lithium battery system.  Each  pack  support  16packs  in  parallel  to  easily expand capacity. Do not mix parallel the battery packs of different brands or models. 1.   Functions l Battery voltage calculation: 16 battery voltage sampling test, deviation ± 20mV l Battery and ambient temperature detection: 4 battery temperature sensors, 1 ambient temperature sensor, 1 MOS temperature sensor, deviation ± 2 ℃. l Battery capacity and cycle times: complete a complete charging, discharging cycle to set the actual capacity. Monitor the remaining capacity of the battery with the capacity estimation accuracy within 5% deviation. In addition, the charging and discharging cycle time and the complete charging and discharging cycle time can be configured. l Smart cell balance: charging and static balance strategies can be flexibly set to effectively extend the service life. l Communication interface: PC or intelligent front-end can monitor battery data, control operation and set parameters through telemetry, remote signaling, remote adjustment, remote control and other commands. The communication protocol meets the requirements of YD/T 1363.3 and realizes cascade communication l Historical data recording, saving and reading: when the battery is abnormal, record and save real-time battery status and alarm information. At present, up to 500 historical fault data can be stored. l Battery management system parameter setting: battery management system parameters, including cell battery over voltage/under voltage, battery total voltage over voltage/under voltage, charge and discharge over current, battery high/low temperature, battery capacity, working mode, charge and discharge limit current, can be set in the battery monitoring system. l Working mode: charging and discharging current limiting, constant voltage output, direct output and other working modes can be set in the monitoring system   l Multiple protection functions: hardware protection, battery protection, high and low temperature protection, output short circuit prot